Third Ear Magnetic

Absolute Industrial

Archive October 2018

MANUFACTURING OF PAPER COFFEE CUPS

A paper cup with lids is basically a disposable cup made of paper and is coated with plastic or was, to avoid any kind of liquid from leaking out. It is made of re cycled paper and it is widely used all around the world. Paper cups were invented in imperial China, in 2nd century BC. Paper cups were constructed in different shapes, sizes and colours and were known as Chih pei. Paper cups were used to serve tea in past centuries. Later, the modern paper cup was developed in the 20th century. Paper cups are also used in hospitals for health reasons. 

The base of paler coffee cup is called cup board. It is made on a special paper machines. They are made water proof. As the paper needs a higher amount of stiffness.. The paper coffee cups forming process requires good extending properties of the board and also the plastic coating. A properly formed mouth roll gives stiffness to the cup. It is also easy in handling. The basic weight of a normal cupboards are around 170-350 g/m. The paper coffee cups are mostly made from non recycled materials. The paper cup has an extra layer to prevent heat when it is held in hands. For example, when a coffee is poured in the paper cup, but due to the extra layer of heat retention, heat will not be able to reach the hand. It is called as a corrugated layer. Paper cups basically for hot drinks are glued up together, and a small amount of clay is dropped in the bottom of the cup. When the clay is dropped it starts to spin really very fast so that it easily reaches the walls of the cup. By this method the paper becomes water resistant. But one disadvantage of this method is that cup board can be smelled and tasted in the cup when any of the beverage is poured in. Water proofing is mostly done fir hot drinks. Whereas cups for cold drink are not treated like that. Those cups which are used for cold drinks etc are actually sprayed on the both sides, either it is outside or inside with wax. But this technique is old now. As a new techniques has been introduced. The new technique which is invented is of using polyethylene. Polyethylene is a method in which it covers the surface of the board with a thin layer of polythene making the cup water proof and also welds the seams together. Later paper cups are printed after they are water proofed.

Printing of paper cups is known as flexography. But now another development is introduced known as direct-printing, it allows printing on a very small quantities.

What Should You Do During Motorcycle Breakdown?

Engine is the heart of the bike. Change the engine oil when it is necessary. Using old oil will reduce the efficiency of the bike. Always maintain the correct level of engine oil.

People who have bikes know how much difficult it is when it breaks down in the middle of the road. It is not fault of the bike. In fact, as a combination of various machines, a bike is subject to wear and tear both on the outer and inner parts. Our negligence can make us ignore some problem that is making its way into the bike. These things can easily cause break down in the road. Though one can avoid some of the problems by regular maintenance, all of them can never be avoided. So it is better to know what you should do when your motorcycle breaks down.

Tyre punctures:

This is one of those problems that cannot be avoided. Hope no one suffers this when on road. There are two types of tyres. One is tubeless and the other is with tube. If your bike is one with no tube I the tyres, you can fix it easily. It is better to keep a kit with you. Read the instructions on the kit and fix the puncture. Make sure to check the tyre pressure at the next station. But if your bike has tubes, it may create a problem. Without a kit in the secluded place, you will definitely be in big problem. The only option is to go to the next repair shop or clutch suppliers by pushing your bike for help. But before pushing loosen the valve nut to keep your tube.

A dead battery:

You need not to worry if there is such a problem. You just need a friend with bike and a cable suppliers from Australia. Connect the positive negative side of your battery with your friends. Don’t switch off the engine. The battery will take charge from the live one. Again you bike will run properly. If you are writhing under the pain of not having a jump cable, there is still way to start the bike. Make good use of the clutch and not the handbrake cables. Push the bike putting it in second gear. Hold the clutch until the bike attains speed. Suddenly leave the clutch to start the bike. Again hold the clutch and give the throttle a twist. Fuel will pass to the engine to keep it running.

4 Tips To Help You Design Your Next Business Sight Well

Setting up a new business site is a big step. It’s a sure fire sign that the business is growing and everything needs to be done well if the business is to gain anything from it. In order to be successful, the business site needs to be designed well and this can be a rather long and hard process. However, if you design things the right way there is a higher chance of success and that’s what’s important. Here are some tips to help you design your next business sight well.

Do your research

When designing a business sight especially for production purposes there are a lot of technical things you need to pay attention to. Things like wiring, commercial poly fittings, air pressure are just some things that might baffle anyone without prior exposure. Even though you will be getting the assistance of professionals to help you out it’s always best to have some form of understanding on what you are doing. An article or two just like this one might be all you need.

Test things out

In any design process prototyping and testing is very important because we have no idea how something might behave until we see it happen. You might be able to hypothesise what will happen but taking the time to test out your ideas before committing to them will make things a whole lot easier for you. When testing makes sure you don’t spend a lot of money and be open to making changes as you will surely have to do this.

Using the right equipment

When building something especially for business quality is a very important thing. You need to makes sure that what you are designing will last a long time and will be able to do the things that need to be done. Even if it’s something small like a poly pipe make sure you get the best quality items that are within your budget as this can save a lot of money as you will be needing fewer repairs.

Be open to change

No matter how awesome your design might be there will be situations where you will have to change. Never be firm in one decision and if the professionals have other ideas to entertain them because they have more experience and therefore might have a better insight.